Stolzer & Son's Gunsmithing

Making dreams of the past a reality tomorrow.

Finished 8 Bore Boxlock

Muzzleloader, Muzzleloading, Big Bore Rifle, Big Bore Muzzleloader, Double Rifle, Muzzleloading Double Rifle, Side by Side, Side by Side Muzzleloader, SxS Muzzleloader, Large Bore Muzzleloader, Muzzleloading Double Rifle, Muzzleloading Side by Side, Muzzleloading Rifle, Black Powder Rifle, Black Powder Muzzleloader, Black Powder Double Rifle, Custom Muzzleloader, Custom Big Bore Rifle, Custom Double Rifle

view:  full / summary

8 Bore Boxlock M/L part 19

Posted on May 6, 2009 at 12:16 PM

Finished and Ready to ship:


I finished up the rest of the bluing yesterday and this morning. Sorry about the photo quality it's overcast and getting decent light was a bit iffy this morning.

Here's the finished rifle ready to go:


Read Full Post »

8 Bore Boxlock M/L part 18

Posted on May 5, 2009 at 10:31 AM

Load development and sighting:


I went out to my range this morning while the weather was nice and calm. I started at 25 yrds working up a load, and then moved back to 60 yards for sighting in. 60 yards was the customers requested distance. Which is actually a very classic distance, 60 yards corresponds to the measurement of 10 rods which was a traditional British distance for big bore rifles.

The Target pretty much speaks for itself:


Read Full Post »

8 Bore Boxlock M/L part 17

Posted on May 4, 2009 at 5:16 PM

I'll make a long story short here for those who have been following along with this build. I sent this out to be engraved because I felt that the wildlife was beyond my engraving skills, it was shipped the third week of January. The engraver I sent it to had other work in front of it and wasn't able to get to it for a few weeks. When the time came to engrave this action he had equipment problems, and needless to say the company providing him with replacement part made a considerable mess of g...

Read Full Post »

8 Bore Boxlock M/L part 16

Posted on February 1, 2009 at 10:24 PM

Checkering:


Some checkering I do in house, others I send out to have done, it just depends on how complex a pattern is desired and how fine a line of checkering is wanted. In this case I checkered this pattern.


Read Full Post »

8 Bore Boxlock M/L part 15

Posted on January 26, 2009 at 5:38 PM

Bluing the Small Parts


As I've mention in previous posts, I've been polishing the metal in between finishing the stock. So today since I had all the small parts polished up and I don't like leaving them around to rust in between now and when I finish the rest of the build, I Rust blued them and oiled them today.


Read Full Post »

8 Bore Boxlock M/L part 14

Posted on January 23, 2009 at 12:20 PM

Stock Finish part 2


This part of a build doesn't make for very impressive updates, it's a lot of the same over and over again, wit very little change to show for it. With the staining done, I have moved onto hand rubbing an oil finish into the stock. It currently has 8 hand rub coats on it, with probably 10 or 12 more to go. The pictures really don't do justice to this wood. It has a beautiful figure and depth the camera just can't capture. The weather today isn't being very...

Read Full Post »

8 Bore Boxlock M/L part 13

Posted on January 16, 2009 at 8:02 PM

Stock Finish and Polishing


I finished sanding the wood today and applied the first coat of stain this evening. Tommorrow morning I can sand it down and apply the next coat.



Read Full Post »

8 Bore Boxlock M/L part 12

Posted on January 14, 2009 at 7:10 PM

Forearm and Ramrod:


Yesterday, I shaped the forearm, and this morning I inlet for the eschuteons. Then this afternoon I turned the ramrod tip anf fit it to the ramrod. I then notched the end of the ramrod to create a locking point for the ramrod, so it doesn't work forward from recoil.



Read Full Post »

8 Bore Boxlock M/L part 11

Posted on January 11, 2009 at 10:35 AM

Stock Shaping


With all the major furniture pieces inlet, I then went to work on shaping the buttstock yesterday. I started by bandsawing the sides down slimmer. Then I went after it with hand planes, chisels and rasps, then files. It's still very rough right now but it's starting to look like a rifle.

Read Full Post »

8 Bore Boxlock M/L part 10

Posted on January 9, 2009 at 7:13 PM

Buttplate


I moved to the back of the rifle today and inlet for the buttplate.


Photobucket

Read Full Post »

Rss_feed